2015 Cross Wrap Oy BO 4000
Hrs.
24
2015 Cross Wrap Oy BO 4000
Year
2015
Hrs.
24
Condition
Used
1
of
25
2015 Cross Wrap Oy BO 4000
1
of
25
Overview
Description
Technical data of the bale opener line:
Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland
Type BO 4000
Year of manufacture 2015
Quantity of opened bales 674 pieces
Operating time only 3 days, exclusively by running in the entire line during new installation
Opening time approx. 45 seconds per bale
Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm
Max. Bale weight 2,000 kg
Conveying height of the system 1,400 mm
Max. Conveying width of the system 1,200 mm
Material to be opened RDF/MSW
Availability of the line 98%
Noise level of the bale opener line 85 dB(A)
Total connected load 37 kW
Rated current 125 A
Operating display SIEMENS SIMATIC HMI Touch
Control SIEMENS S7 ET200S
Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h)
Scope of delivery:
Feed conveyor 3,500 x 1,200 x 1,400 mm
Feed conveyor to opener 1,500 x 1,200 x 1,400 mm
Bale opener (gripper with knife)
Special equipment:
Oil heating in hydraulic oil tank
Heating in control cabinet
Oil cooler in Hydraulic unit
Explanation of the short period of use:
The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process.
This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale.
Short description of the wrapping process:
The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system.
Comments:
New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.
Technical data of the bale opener line:Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland
Type BO 4000
Year of manufacture 2015
Quantity of opened bales 674 pieces
Operating time only 3 days, exclusively by running in the entire line during new installation
Opening time approx. 45 seconds per bale
Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm
Max. Bale weight 2,000 kg
Conveying height of the system 1,400 mm
Max. Conveying width of the system 1,200 mm
Material to be opened RDF/MSW
Availability of the line 98%
Noise level of the bale opener line 85 dB(A)
Total connected load 37 kW
Rated current 125 A
Operating display SIEMENS SIMATIC HMI Touch
Control SIEMENS S7 ET200S
Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h)
Scope of delivery:
Feed conveyor 3,500 x 1,200 x 1,400 mm
Feed conveyor to opener 1,500 x 1,200 x 1,400 mm
Bale opener (gripper with knife)
Special equipment:
Oil heating in hydraulic oil tank
Heating in control cabinet
Oil cooler in Hydraulic unit
Explanation of the short period of use:
The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process.
This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale.
Short description of the wrapping process:
The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system.
Comments:
New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.
Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland
Type BO 4000
Year of manufacture 2015
Quantity of opened bales 674 pieces
Operating time only 3 days, exclusively by running in the entire line during new installation
Opening time approx. 45 seconds per bale
Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm
Max. Bale weight 2,000 kg
Conveying height of the system 1,400 mm
Max. Conveying width of the system 1,200 mm
Material to be opened RDF/MSW
Availability of the line 98%
Noise level of the bale opener line 85 dB(A)
Total connected load 37 kW
Rated current 125 A
Operating display SIEMENS SIMATIC HMI Touch
Control SIEMENS S7 ET200S
Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h)
Scope of delivery:
Feed conveyor 3,500 x 1,200 x 1,400 mm
Feed conveyor to opener 1,500 x 1,200 x 1,400 mm
Bale opener (gripper with knife)
Special equipment:
Oil heating in hydraulic oil tank
Heating in control cabinet
Oil cooler in Hydraulic unit
Explanation of the short period of use:
The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process.
This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale.
Short description of the wrapping process:
The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system.
Comments:
New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.
Show more Show less
